Please wait while the page loads...

How many miles can you drive with the check engine light?

Since each check engine code has its own level of severity, it is necessary to predict how many miles you can commute with the warning light on. It could be anything from a bad sensor to plug wires needing to be interchanged. If you check engine light is flashing, we endorse that you pull over and contact Coggin Deland Ford to help read if your vehicle is safe to commute in or if we endorse a tow truck. The safest bet is to decipher the code and then plan your strategy accordingly.

2013 Ford Fusion Check Engine Light Flashing

Although there are countless potential causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are several basic causes including something as straightforward as a loose gas cap. Further basic reasons for a Check Engine Light are a malfunction with the fuel injection system, faulty head gasket, dirty mass airflow sensor, damaged oxygen sensor, faulty emissions control part, or defective spark plugs to name some. No matter what is the root cause of the Check Engine Light, we have the Ford Certified Technicians and the certified service protocol to isolate the root problem and repair it as imperative to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Ford issue was fixed.

Every 2013 Ford Fusion was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the vehicle on its necessary systems. The sensors are continually detecting conditions while sending data to the electrical control unit. If the electrical control unit detects that the data is out of factory specifications, the Check Engine Light illuminates telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what exactly is inaccurate nor what to do about it. That’s where we come in; Coggin Deland Ford provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Greatly Qualified Service professional.

2013 Ford Fusion Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that microscopic light on your vehicle’s dashboard suddenly flashes, but in reality, it is not something that should cause you to shut down in fear proper away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, also prevailing as the OBD (on-board computer diagnostic system) in your Fusion. There are hundreds of assorted codes that your check engine light can represent. While that sounds daunting, with a few patience, tackling imperative diagnostics will give you useful knowledge about your vehicle and will also allow that Check Engine Light to do what it is genuinely supposed to do: be your guide. Unfortunately, obvious and handy vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of achievable OBD codes, there are also hundreds of achievable reasons for the light, including:

  • Transmission issues
  • Computer output circuit issues
  • O2 Sensor
  • Ignition system faults
  • Old Battery
  • Bad Spark Plugs
  • Fuel and air metering systems problems
  • Emissions controls issues
  • Loose Gas Cap or Missing Gas Cap

This is why it is important for someone who does not have a lot of automotive knowledge to not assume what a code means. If the engine light comes on due to a hazardous concern, you risk damaging your car further by not repairing the issue proper away. When your check engine light comes on, you should get it checked out immediately by a certified Ford mechanic. Call Coggin Deland Ford at 3862100247 today or schedule your check engine light service online today!

Check Engine Light Service 2013 Ford Fusion

What do you do when you’re driving along in your Ford Fusion and suddenly, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Ford owners, your heart sinks a miniature because you have miniature idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the estimate of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t mean you have to pull the car over to the side of the road and call a tow truck, but it is recommended that you get your 2013 Ford Fusion checked as soon as achievable. Ignoring that warning could end up causing gigantic damage to expensive engine elements.

When your 2013 Ford Fusion's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t noble, a computer turns on your check engine light. This amber or yellow light is typically labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it's a sensor or a failing engine part. This code is determine with an electronic probe tool that is used by our Ford auto repair mechanics at Coggin Deland Ford. There are also a number of comparably bargain code readers that are designed for do-it-yourselfers, should you choose that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an experienced professional to determine the issue and repair it.

How much does it cost to get the engine light checked?

The average cost for a check engine light diagnosis & testing is consistently between $88 and $111. The correct news, Coggin Deland Ford offers complimentary multi-point inspections and free diagnostics, in most cases, to aid find out the cause of your check engine light. The check engine light warns of issues ranging from a gas cap that's not correctly tightened to a more alarming failure like a bad catalytic converter or a problem with one of the car's oxygen sensors, so it correct to get the constitutional code reading and diagnosis.

Will the check engine light reset itself?

The check engine light on your 2013 Ford Fusion will ordinarily shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will turn itself off. Likewise, if your catalytic converter is going rational, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your 2013 Ford Fusion light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to bring it in to Coggin Deland Ford so the light and code can be double-checked and reset.

Is it safe to drive your 2013 Ford Fusion with the check engine light on?

This question is not particularly pure because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be safe to drive. This is naturally indicated by a consistent glow of the check engine light. If you notice a difference in the performance of the car, it could be an indication of a more astonishing problem. If the check engine light is twinkling, this means that there is a astonishing issue and it is recommended to service your Ford Fusion expeditiously. Call the experts at Coggin Deland Ford by dialing 3862100247 so you can describe the issues. Or cut your speed and bring your 2013 Ford to our certified mechanics as soon as achievable.

What could cause the check engine light to come on in a 2013 Ford Fusion?

When your check engine light comes on, this could be as easy as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a adequate problem that could cause adequate damage to your engine and come with a major repair bill. Depending on your make and model, the check engine light will illuminate or blink. A persistent glow generally means something less adequate but a flashing check engine light suggests that your vehicle’s engine is in adequate trouble and service is mandatory suddenly. If your check engine light is flashing in your 2013 Ford Fusion, we highly suggest not to drive the vehicle and schedule Ford service today. Below is a list of the most common reasons your check engine light can come on:

  • Your O2 Sensor (Oxygen Sensor) needs to be changed. The Oxygen sensor, known as the O2 sensor, measures the amount of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your vehicle will be fewer compelling when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause damage to your catalytic converter and your 2013 Ford Fusion's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to express the right mixture of air and fuel that enters the cylinders in your engine. A bad O2 sensor can also cause a car to fail an emissions test.
  • Your catalytic converter is bad or going bad. The catalytic converter is a part of your 2013 Ford Fusion’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is usually caused by neglected maintenance, which is why Coggin Deland Ford offers a complimentary multi-point inspection with every Ford service. If you have an issue with your catalytic converter and don't get it repaired, your 2013 Ford Fusion will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause additional problems from overheating.
  • Your 2013 Ford Fusion has a vacuum leak. Every Ford Fusion has a vacuum system that performs a great variety of functions. The vacuum system also helps lower harmful emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dry out and crack, chiefly if they’re exposed to important heat or extreme afraid.
  • The battery is low or dead. The battery in your 2013 Ford Fusion is every favorable. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did a few decades ago, and they don't absolutely require maintenance. The value of a new one depends on the type of Ford you travel to work, but check our brand-new service coupons and specials.
  • New Spark Plugs or Plug Wires are crucial for your 2013 Ford Fusion. The spark plugs are the part of your engine that ignites the air/fuel mixture in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run. The spark plug wires transport the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are bad or erstwhile, you will experience poor performance and reduced power. In some extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, major to more expensive repairs.
  • One of the most natural and copious cause is that your 2013 Ford Fusion gas cap is loose, damaged or missing. The gas cap for your 2013 Ford Fusion serves multiple purposes. It prevents gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a bad fuel cap? If your gas cap is erstwhile or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on instantly after you put gas in your 2013 Ford Fusion, first thing you should check is to make confident the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
  • Your mass airflow sensor (known as MAF) needs to be changed. The mass airflow sensor in your Ford Fusion is what determines how much fuel is crucial to run your engine efficiently by measuring the amount of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to affable changes, like altitude. If your Ford Fusion is having trouble starting, idling rough or has a sudden change in the position of the throttle pedal, this could be a sign of a bad mass airflow sensor.
  • Issues with each aftermarket items. An aftermarket alarm, exhaust or additional item can wreak havoc on your 2013 Ford Fusion if it’s not installed correctly. These aftermarket elements and accessories can drain the battery, trigger the check engine light, or even avoid the vehicle from starting. If these issues sound prevailing, bring your Fusion to Ford and have our team of certified mechanics ensure that your aftermarket items were installed correctly and aren't causing each issue. Getting accessories, chiefly aftermarket parts and accessories, or using OEM elements first place might value a small bit more but could save you money from having to get poor work and damage caused by poor installation work corrected.

What Does the Check Engine Light Mean?

One of the most typically misunderstood lights or indicators in your 2013 Ford Fusion is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in a lot contrasting ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your vehicle. Onboard computers increasingly have controlled and monitored vehicle performance since the 80s and do a range of things for your 2013 Ford Fusion. Some of these include ignition timing, shifting automatic transmissions controlling engine speed, and implementing stability control, just to name some. With that being said, the check engine light can mean a variety of different things. It can be as easy as your gas cap being loose or as adequate as engine knocking. If your check engine light is on in your 2013 Ford Fusion, contact Coggin Deland Ford. Contact Coggin Deland Ford today! Our Ford service department can aid you find out what code is turning your check engine light on or diagnose why your check engine light is flashing.

2013 Ford Fusion Check Engine Light

If the check engine light in your 2013 Ford Fusion starts flashing, that means that the problem needs immediate attention and your Ford should be delivered in expeditiously. A flashing light implies that the problem is draconian and if not taken care of expeditiously may result in vast damage to the vehicle. This glaring light usually indicates a rigorous engine misfire allowing unburned fuel to be dumped into the exhaust system. There it can swiftly increase the temperature of the catalytic converter to a point where damage is probable, requiring an expensive repair. Some owners ask if spark plugs cause the check engine light to flash? This can certainly be the cause. A bad, traditional or dirty spark plug can cause the engine to misfire. If your check engine light is flashing, please contact our company of automotive experts at Coggin Deland Ford immediately by calling 3862100247. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a particularly expensive repair.